|
 |
BUILDING A BETTER WORLD |
|
|
|
|
|
|
|
|
|
| Below-grade Waterproofing |
|
| Carlisle Sheet
Membrane Waterproofing System: consists of a 56 mm
thick rubberized asphalt membrane which is laminated to high density 4 mm
polyethylene film on the face and siliconized release sheet on the adhesive side.
The sheet membrane is available in 36" width. The system provides a
non-sag mastic for sealing terminations of the sheet membrane. The factory
controlled thickness assures uniform thickness on the job while the inherent waterproofing
properties of the rubberized asphalt and the polyethylene film provide an excellent water
barrier. |
|
| Packaging: CCW-701-36 = 36 inches wide X 67 ft. roll (200 sq. ft.) 25 rolls per pallet (5000 sq.
ft.) - Weight = 82 lb/rl (approx.) |
|
|
|
|
|
|
| Typical
Use: The system is suitable for a wide variety of applications such as
waterproofing below-grade foundation walls, earth shelters and tunnels. It is also
suited for waterproofing between the structural slab and wearing course on parking decks,
plaza decks, mud slabs, terraces, balconies, equipment rooms, kitchens, bathrooms and
laboratories. |
|
|
|
Limitations:
- Not recommended in areas where membrane will be
subject to continuous exposure to sunlight.
- Optimal results are obtained when applied at
temperatures between 25 and 40 degrees Fahrenheit.
- Do not apply membrane to a damp, frosty or
contaminated surface.
|
|
| Packaging:
CCW-701-36 = 36 inches wide X 67 ft. roll
(200 sq. ft.) 25 rolls per pallet (5000 sq. ft.) - Weight = 82 lb/rl (approx.) |
|
|
|
|
|
|
| Application on Horizontal
Surfaces: Apply CCW-701 Sheet from low to high point so that laps will shed
water. Overlap edge seams 2 1/2 inches, end seams 4 inches and staggered. Snap
a chalk line for a starting point. Pull 2+ feet of release paper and place adhesive
side of membrane along chalk line. As the roll is dispensed, simultaneously roll the
release paper and maintain alignment along the chalk line. Immediately after
installation, roll sheet with metal roller wrapped with a resilient material. Roller
should be 18 to 24 inches wide and weigh at least 100 lbs. Application on Vertical Surfaces: Apply CCW-701 Sheet
Membrane in lengths of 8 feet or less. Overlap edge seams 2 1/2 inches. On
walls above 8 feet, apply in 8 foot sections, starting at the lowest point with the higher
section overlapping the lower section 4 inches. Use a suitable roller to press
membrane firmly against wall.
Note: Failure to use adequate pressure at
terminating edges will result in a poor seal and potential leak. The use of mastic
is not a substitute for a good seal. |
|
|
|
|
|
| Protection: CCW-701
Sheet Membrane must be protected from damage by future operations and other trades.
The applicator shall install suitable protection course material to protect the
membrane. The protection course may be CCW SURE-DRAIN (H or V) or CCW PROTECTION
BOARD (H or V). Install protection course on
vertical walls immediately after installation of the CCW-701 Sheet Membrane and backfill
as soon as possible.
Storage: Protect materials from
excessive heat and cold. Store materials away from flames or sparks. Outside
storage: Protect from rain, direct sunlight or harmful environmental conditions.
|
|
|
| Call
PolySteel
Northeast for purchase price: toll free
1.866.4PolySteel
|
|
|
|
|
|
|
|
Please
report problems to john@polysteelnortheast.com
© Polysteel Northeast, LLC 2000. All Rights Reserved.
No part of this website may be reproduced or used without express and written permission
from the owner.
Polysteel® and
Polysteel Form® are registered trademarks of American Polysteel Forms. |
